Download

* Note: All the wire length above is the original length, not the length you see from the outside..

* Note: All the wire length above is the original length, not the length you see from the outside..

The F3 processor ensures no input commands are missed, even at the highest input update rates. Its bleeding-edge features include PWM-frequency dithering, and Active Phase-current Demagnetization to ensure the smoothest control at high power, while sustaining maximum efficiency.

Compatible with the latest Protocols including ProShot up to 3MBs/S.

With peak power ratings up to 9kW, these ESCs will have no trouble powering your craft.

Feature Set:

• Designed and manufactured in Australia using only the highest quality components, ensuring no sacrifice in reliability.
• Plug and play firmware
• Up to 12S capable
• True 10bit resolution
• 200A Burst current
• Up to 120Amps continuous* current
• Virtually no setup time, with simple motor reverse solder tab
• Telemetry output
• Auto-detect ProShot or Dshot any frequency range
• Intelligent current sensing
• Dshot300 to Dshot1200 capable (0.3-1.2Mbs/s)
• ProShot1000 capable (1Mbs/s)
• Auto PWM-freq
• Auto Timing Advance
• HBM (Hectic Boost Mode) ensures this will deliver maximum thrust, outperforming any other ESC
• 8-Layer PCB to ensure minimal track resistance
• LED indication
• Digital commands over Proshot (including anti-turtle mode)
• Digital commands over Dshot

* Continuous current ratings are at a 100% throttle duty cycle. Continuous rating is defined as max sustained current at 100% throttle for 60 seconds with 33 m/s airflow.

Documentation and Datasheets can be found at: docs.powerdrives.net

• High performance 32-bit microprocessor with the running frequency of up to 48MHz for excellent performance.
• BLHeli_32 firmware is the third generation BLHeli, following base BLHeli and BLHeli-S.
• Dshot signaling is supported at any rate up to at least Dshot1200. The input signal is automatically detected by the ESC upon power up.
• All codes use damped light mode. Damped light does regenerative braking, causing very fast motor retardation, and inherently also does active freewheeling.
• The code supports features to prevent sync loss. There are tunable parameters that can make the code run well even in the most demanding situations, although default settings will work excellently in normal operating environment
• The code supports regular 1-2ms pulse width input, as well as Oneshot125 (125-250us), Oneshot42 (41.7-83.3us) and Multishot (5-25us).
• The code also supports a beacon functionality, where the ESC will start beeping after a given time of zero throttle. This can be very useful for finding lost crafts.

The XRotor Micro Combo from Hobbywing continues to impress with it's latest iteration. The Micro Combo features a 60A 4-in-1 ESC along with an updated G3 Flight Controller. This new FC is similar to the G2 with its F4 processing, OSD, and voltage monitoring, but the G3 now also comes with an all-new 12V@2A BEC.

Make your electronics stack work for you, not the other way around. 

Features

F4 G3 FC

• Super-high Running Frequency. The STM32F405 MCU which features the powerful computing capability and super-high running frequency allows the FC to run the PID and gyro with higher frequency.
• ProShot1000, DShot 150/300/600/1200, Oneshot125, Oneshot42, Multishot Modes Supported. Besides the latest ProShot, Dshot 150/300/600/1200 mode, the FC also supports the regular PWM mode, Oneshot125 mode, Oneshot42 mode, and Multishot mode.
• Onboard OSD Microchip. Onboard OSD microchip allows users to easily adjust various (OSD) parameters via the Betaflight/Cleanflight software.
• TF-card Insertion Supported. Onboard OSD microchip allows users to easily adjust various (OSD) parameters via the Betaflight/Cleanflight software.
• The FC, which supports Betaflight/Cleanflight firmware & allows parameter adjustment via Betaflight /Cleanflight software, is more applicable to FPV flying & racing.
• BetaFlight/Cleanflight Firmware Ready

60A 4-in-1 ESC

• High-performance 32-bit microprocessor with the running frequency of up to 48MHz for an excellent performance.
• BLHeli_32 firmware is the third generation BLHeli, following base BLHeli and BLHeli-S.
• Onboard 10V &5V BEC, powering different accessories such as FC, VTX, Camera and LED lights and etc.
• All codes use damped light mode. Damped light does regenerative braking, causing very fast motor retardation, and inherently also does active freewheeling.
• The code supports features to prevent sync loss. There are tunable parameters that can make the code run well even in the most demanding situations, although default settings will work excellently in normal operating environments.
• The code supports regular 1-2ms pulse width input, as well as Oneshot125 (125-250us), Oneshot42 (41.7-83.3us) and Multishot (5-25us).
• Dshot signaling is supported at any rate up to at least Dshot1200. The input signal is automatically detected by the ESC upon power-up.
• The code also supports a beacon functionality, where the ESC will start beeping after a given time of zero throttles. This can be very useful for finding lost crafts.

Specifications

F4 G3 FC

• Firmware: OMNIBUSF4SD
• FC Programming: Supported
• Programming via: Betaflight/Cleanflight-configurator or Others
• Compatible with (Transmitters): PPM, Spektrum, SBUS, SUMD, SUMH, XBUS, IBUS, JETIEXBUS, CRSF, SRXL, and etc.
• Compatible with (Modes): PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, DShot1200, Proshot1000 and etc
• BEC: 12V @2A
• OSD: Built-in
• Current Monitoring: Supported
• Voltage Monitoring: Supported
• LED Control: Supported
• External Buzzer: Supported
• Timing: Supported
• Motor Rotation: Supported
• USB Port: MicroUSB
• Size: 36x36mm
• Mounting Holes: 30.5x30.5mm
• Weight: 6g

60A 4-in-1 ESC

• LiPo Power input: 3S-6S
• Cont.Current: 60Ax4
• Burst Current: 80Ax4
• BEC Output: 5V@ 0.5A
• Input wires: 12AWG-130mm* (Red/Black)
• Output Wire: No wires but solder tabs
• Connectors: (In/Out) XT60 (w/ Wires Soldered on) /no
• Weight / Size: 15.0g / 32.7x18.4x6.2mm
• Throttle Calibration: Supported
• Mounting holes: 30.5x30.5mm
• ESC Programming: BLHeliSuite32

Includes

• 1 x F4 G3 FC
• 1 x 60A 4-in-1 ESC
• 1 x Signal Cable
• Soft Mounting Grommets